Die war gar nicht mehr ansprechbar. (Bis auf die Firmware)
Code: Alles auswählen
$ sudo smartctl -a /dev/sdb
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.10.0-35-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST31000524AS
Serial Number: 9VP9XXXX
LU WWN Device Id: 5 000c50 xxxx
Firmware Version: JC4B
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Sep 20 16:53:01 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Read SMART Data failed: Die Wartezeit für die Verbindung ist abgelaufen
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: Die Wartezeit für die Verbindung ist abgelaufen
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.
Read SMART Log Directory failed: Die Wartezeit für die Verbindung ist abgelaufen
Read SMART Error Log failed: Die Wartezeit für die Verbindung ist abgelaufen
Read SMART Self-test Log failed: Die Wartezeit für die Verbindung ist abgelaufen
Selective Self-tests/Logging not supported
Also nach knapp 5 Jahren. Dabei muss man bedenken, dass der Server 24 Stunden, 7 Tage die Woche läuft. Allerdings wechselt der Server periodisch die zu beschreibende Platte. Somit wäre das Pi mal Daumen 2,5 Jahre dauernder Schreibzugriff. Gar nicht schlecht.
Allerdings muss ich mir nun wieder eine neue Reserveplatte zulegen.
Code: Alles auswählen
$ sudo smartctl -a /dev/sdb
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.10.0-35-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST31000524AS
Serial Number: 9VPFXXXX
LU WWN Device Id: 5 000xxx xxx
Firmware Version: JC4B
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Sep 20 17:04:30 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: Die Wartezeit für die Verbindung ist abgelaufen
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 163) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 109 099 006 Pre-fail Always - 239754929
3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 223
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 4421120949
9 Power_On_Hours 0x0032 051 051 000 Old_age Always - 43711
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 86
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 078 078 000 Old_age Always - 22
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2
190 Airflow_Temperature_Cel 0x0022 073 055 045 Old_age Always - 27 (Min/Max 27/27)
194 Temperature_Celsius 0x0022 027 045 000 Old_age Always - 27 (0 15 0 0 0)
195 Hardware_ECC_Recovered 0x001a 027 010 000 Old_age Always - 239754929
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 43539 (81 13 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1044449302
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1977762853
SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 12 occurred at disk power-on lifetime: 43703 hours (1820 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:01:36.741 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:36.673 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:33.911 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:33.834 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:31.088 READ FPDMA QUEUED
Error 11 occurred at disk power-on lifetime: 43703 hours (1820 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:01:33.911 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:33.834 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:31.088 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:31.020 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:28.283 READ FPDMA QUEUED
Error 10 occurred at disk power-on lifetime: 43703 hours (1820 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:01:31.088 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:31.020 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:28.283 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:28.156 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:25.410 READ FPDMA QUEUED
Error 9 occurred at disk power-on lifetime: 43703 hours (1820 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:01:28.283 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:28.156 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:25.410 READ FPDMA QUEUED
61 00 08 38 ea 07 40 00 00:01:25.410 WRITE FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:25.342 READ LOG EXT
Error 8 occurred at disk power-on lifetime: 43703 hours (1820 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:01:25.410 READ FPDMA QUEUED
61 00 08 38 ea 07 40 00 00:01:25.410 WRITE FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:01:25.342 READ LOG EXT
60 00 08 ff ff ff 4f 00 00:01:22.626 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:01:22.587 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.